Check your microphone in ten seconds
- Press Start and allow the microphone when your browser asks. If you have more than one, pick it in the Microphone list.
- Stay quiet for 3 seconds while the background noise is measured, then talk or clap for 5 seconds at your usual distance.
- Read the noise floor, the loudest peak, clipping, mains hum and sample rate, and play your 5 seconds back.
- Change the input level or move the microphone, then press Try again to compare.
How the result is worked out
The test asks for the microphone with echo cancellation, noise suppression and automatic gain turned off, because each of them would change the levels it measures. It reads the raw samples many times a second. While you stay quiet, it splits the sound into 50 ms windows, works out the RMS level of each in dBFS (decibels below full scale, where 0 dBFS is the loudest a recording can hold) and takes the median as the noise floor, so one cough barely moves it. Over the same 3 seconds it averages the spectrum and reports mains hum when a peak within about 1 Hz of 50 or 60 Hz, or of 100 or 120 Hz, stands at least 10 dB above the median level between 20 and 300 Hz. While you talk, the highest sample is the peak, and every run of samples at 99.9% of full scale or more counts once as clipping.
What changes the result
- Input level: the level in your system’s sound settings scales every number here, so change it and check again.
- The room: fans, traffic and computer noise raise the noise floor, so measure where you will actually record or call.
- Distance: talking closer gives higher peaks and a greater chance of clipping.
- Cables and power: microphones and headsets near chargers, power leads or a laptop on its charger can pick up mains hum.
- Bluetooth headsets: while their microphone is in use, most switch to a call mode with a lower sample rate, often 16 kHz, which sounds duller.
- Built-in processing: some microphones and drivers clean the sound before the browser gets it, which can lower the noise floor and soften peaks.
About this test
A quick mic check before a call or a recording answers three questions: can the computer hear you, is the background quiet enough, and is your voice clean. This microphone test measures each of them in about ten seconds and lets you hear the result.
The noise floor is the level of everything the microphone picks up when nobody is talking: room noise, fans and the hiss of the microphone itself. It is measured in dBFS, so a lower number, further below zero, is quieter. The loudest peak while you talk shows how much room is left before the sound reaches full scale, and clipping counts the moments it did.
Mains hum is a steady low tone at 50 or 60 Hz, the frequency of the power supply where you are, often with a stronger tone at twice that. It usually comes from cables and chargers rather than the microphone, so the fix is often a different port or lead.
Use this mic test to test microphone settings after changing them: run it, change one thing, such as the input level, the distance or the port, and run it again. The playback lets you hear what others will hear, without any of it leaving your device.
Frequently asked questions
Why does the browser ask to use my microphone?
Browsers never let a page hear the microphone without your permission. The test asks only when you press Start, and the microphone is turned off when the check ends, when you press Stop or Reset, or when you leave the page.
Is my recording uploaded?
No. The 5 seconds you hear back are kept in this page’s memory and are gone when you press Try again or leave the page. Only the numbers of the result are saved, in this browser, and you can clear them in My results.
What is a good noise floor?
There is no single target, because it depends on the microphone, its input level and the room. Lower means less hiss and background noise. Use the number to compare your own setups, such as two microphones or two rooms, at the same input level.
What does clipping mean?
The sound was louder than the recording can hold, so the tops of the wave were cut off and those moments sound harsh. Move back from the microphone or turn its input level down until clipping shows None.
How do I get rid of mains hum?
Hum at 50 or 60 Hz comes from the mains supply. Try another USB port, unplug the laptop charger for a moment, move the cable away from power leads, or use a ground loop isolator with analogue microphones.
Why does it say no microphone was found, or that it is in use?
The system has no microphone turned on, or another app such as a video call is holding it. Plug in or turn on the microphone, close the other app, then press Start again.
References
- W3C. Media Capture and Streams. getUserMedia and the echoCancellation, noiseSuppression and autoGainControl settings the test turns off.
- W3C. Web Audio API. The AnalyserNode the samples and the averaged spectrum are read from, with its Blackman window.
- W3C. MediaStream Recording. MediaRecorder, which keeps the 5 seconds of talking in memory for playback.
Last updated 17 November 2026